A Sneak Peak at How the Carousel Build Will Look and Project Update - Part 29

 This week I was able to put some of the parts of the carousel together to see the shape of things to come for the carousel.  I won't keep readers in suspense.  I am blogging about this first because I know that most readers will want to see that.  This is the first picture.  Although nowhere near completed, it gives me some inspiration for the future of the project.

The bottom platform holds the rotating mechanism (see previous posts for photos of that).  I will post more pictures of it in future posts.  The second platform will be for the animals and will have a plank wood floor overlaying the plywood.  I have not yet decided on whether to cover the first layer with a curtain or leave it open so people can see how the mechanism works.  I cannot completely close it in because the rotating mechanism has an on/off switch and an eye so it can be turned on and off by remote control.  Either way, it needs some kind of access.

At this point, the top looks a little high, but that is because the horse is not yet fitted to the pole.  It is just propped up against it.  Once the horse has the holes drilled for the pole to go through it, the horse will not be standing on the platform.  It will be about a half an inch off the ground.  It needs some head room to make sure that when the horse is moving over the higher section of the bumps below that it has enough clearance to make it look right.

Although the animal forms are complete, they do not yet have the saddles, bridles, or the flower and ribbon decorations.  I did not want to start that part of the project yet until I knew where I needed to drill the holes to mount the animal on the pole.  I cannot begin the painting of the animals until all of that is complete.  For those new to the carousel blogs, I say animals not horses because there are different animals on this carousel.  It will have two horses, a house cat, a tiger, and a ram.  I had seen a carousel once that had those animals and more, and that carousel was an inspiration for this piece.  Although now, seeing this prancing horse on the carousel makes me sort of wish I had made all horses.  I hope that will pass.  I don't want to spend months making more horses, but I remind myself that there is still time.

Imagine the future top of the carousel.  It will not be flat.  I am thinking it will have a multi-colored top that will look like a circus tent.  The protruding parts of the dowels will be cut down to an inch or half an inch above the ball on the roof.  More on the reason for those balls will be in future posts.

The center pillar, which at the moment is a full box of oatmeal to make it sturdy enough to hold up the plywood, will be the oatmeal box reinforced externally and internally to make it strong enough to carry the weight.  It may have some other filler in the center for extra support (but not oatmeal).  Once that is completed it will be painted and probably have some mirrors on it to reflect the animals as they go around the circle.  

Anyway, this is the first glimpse I have had of how the carousel might work.  It is just the basic start of the project, but it has given me a lot of encouragement.  I needed it.  In long term project like this it can be discouraging at times.  When I think of how much work needs to be done to complete it sometimes, I just want to crawl into a corner somewhere.  The only way to combat that is to focus on just the next step.  That is all I have to do today is the next step.  The project will finish in its own time.  

I do sometimes sell a piece when I have held it long enough to become bored with it, but I do not like to do things on commission because I don't like to be under pressure to complete a project.  Some people thrive on pressure, but I am not one of them.  Making things is my "happy place" where I go to escape the stresses of life.  I don't want to complicate that.

Today's project update is to show that the holes have been drilled out for the balls to fit onto the dowels that will be the poles for the horses and the ones that will sit on the roof.  The craft store did not have the balls and wheels with the size hole that I needed.  That is probably just as well, because I am finding that the dowels are not exactly uniform throughout its length.  Even after drilling, I am finding that I need to do a little filing with a small file to make the balls fit where I need them to fit.  Some of them have to be tight enough to hold when glued in place.  Others need to be loose enough to support the dowel but allow for free movement.  

So, as I said earlier, I only need to focus on the next step.  One step at a time this project is moving forward.

Check back next Monday or Tuesday for the next blog post.